Model Range- KW/HP

1 Phase 240V
 0.75-2.2KW

3 Phase 240V  
.75 -15KW  

3 Phase 460V .75-15KW

Voltage Rating

200-240V

200-240V

380-500V

Input Voltage Tolerance

 -10% / +10%

 -10% / +10%

 -10% / +10%

Voltage Regulation

Adjustable within the range of 50-600V by correcting the supply voltage (not adjustable above the input voltage)

PWM Carrier Frequency

Adjustable between 2.0KHz-16KHz. (default 12 KHz/current derate applies above 4KHz)

Control System

Sine Wave PWM System

V/Hz Pattern

Open Loop Vector, Constant Torque, Variable Torque, Auto Torque Boost, Manual Torque Boost, automatic energy saving, dynamic automatic energy saving, PM motor control, Auto Tuning, Base Frequency 25-500Hz, Torque Boost 0-30%; Start Frequency .5-10Hz

Overload Rating

150% for 60 seconds, 200% for .5 second

Frequency Setting

Potentiometer and Digital Input on Front Panel, Remote Potentiometer (1-10KOhms), 0-10Vdc (input impedance VIA/VIB=30KOhm), 4-20mAdc (input impedance 250 Ohm, 15 preset speeds by contact closure)

Frequency Precision

Analog Input ±0.5% of the Maximum Output Frequency, Digital Input ±0.01% of the Maximum Output Frequency

Frequency Command Resolution

0.01Hz Operation Panel, 0.1Hz Analog Input

Output Frequency Range

0.5-500Hz (default 0.5 -80Hz, maximum frequency 30-500Hz)

Frequency Jump

3 Frequencies with Adjustable Range

PID Control

Proportional Gain, Integral Gain and Differential Gain Settings and Control Wait Time

Upper and Lower Limit Frequencies

Upper Limit Frequency: 0 to max frequency, Lower Limit Frequency: 0 to upper limit frequency

Input Terminals

8 input terminals programmable to 65 functions. Logic selectable between sink and source.

Analog Inputs

(1) 4-20mA, (1) 0-10V or 1-10KOhm Potentiometer Connections

Output Contacts

1 Open Collector and 1 Relay contact programmable to 58 functions.

Analog Output

1mA / 7.5Vdc or switch selectable to 0-20mA (4-20mA), programmable to 19 functions

Power Terminals

Input (L1, L2, L3), Output (T1, T2, T3), DCL (PO, PA), DBR (PA, PB), DC BUS (PA, PC)

Protective Functions

Stall Prevention, Current Limitation, Output Short Circuit, Overvoltage, Overvoltage Limitation, Undervoltage, Ground Fault, Power Supply Phase Failure, Output Phase Failure, Overload Protection, Overcurrent at Startup, Overtorque, Undercurrent, Overheat, Cumulative Operation Time, Life Alarm, Emergency Stop, Braking Resistor Overload, Various Pre-alarms   

Retry

ASD can automatically clear fault upon trip. Programmable to 10 times with wait time up to 10 seconds between retry.

Restart

ASD will smoothly catch a freewheeling motor.

Ambient

Temperature: -10-50°C, Humidity 93% non-condensing

Installation

IP20 (enclosed type) /IP 54 available

LED Indications

Run, Monitor Mode, Program Mode, % and Hz Indication, Frequency Setting Mode by Potentiometer or Up/Down Keys, DC Bus Capacitors Charged

Monitoring

Operation Frequency, Operation Frequency Command, Forward/Reverse Run, Output Current, Voltage in DC Section, Output Voltage, Torque, Torque Current, Drive Load , DBR Load, Input Power, Output Power, Monitor of Input and Output Terminals, CPU and Memory Versions, PID Feedback and Frequency Command, Rated Current, Past Trips 1-4, Parts Replacement Alarm, Cumulative Run Time

Selectable Display Units

Current and voltage display selectable between Amps/Volts or % along with scaling factor multiplier.